GCSE Physics Magnetism and Electromagnetism MCQs – 30 Practice Questions with Answers (AQA 8463)
Thirty original practice questions for AQA GCSE Physics (8463), Topic 7 Magnetism and Electromagnetism, covering magnetic poles and fields, compasses, induced and permanent magnets, electromagnets, the motor effect, Fleming’s left-hand rule, the generator effect, alternators and dynamos, transformers and the national grid, and loudspeakers and microphones. Every question has a worked answer hidden underneath it. Use g = 9.8 N/kg in all calculations (where relevant).
Formula recap for Magnetism and Electromagnetism
Force on a current-carrying wire: F = BIl, where F is force in newtons (N), B is magnetic flux density in tesla (T), I is current in amperes (A) and l is length in metres (m). Transformer equation: Vp ÷ Vs = Np ÷ Ns, where Vp and Vs are the primary and secondary voltages in volts (V) and Np and Ns are the numbers of turns on the primary and secondary coils. For an efficient transformer, power in = power out, so Vp × Ip = Vs × Is.
Need the full list? Open the GCSE Physics Formula Sheet (AQA 8463).
Magnetic Fields, Poles and Compasses
Q1. A pupil holds the north pole of one bar magnet close to the north pole of a second bar magnet. What happens?
- (A) The magnets attract each other
- (B) The magnets repel each other
- (C) The magnets have no effect on each other
- (D) Both magnets lose their magnetism at once
Show Answer
Answer: B – Like poles repel and unlike poles attract. Two north poles are like poles, so the magnets push each other apart.
Q2. Which statement correctly describes the magnetic field around a bar magnet?
- (A) The field is strongest at the middle of the magnet
- (B) The field lines point from the south pole to the north pole outside the magnet
- (C) The field lines point from the north pole to the south pole outside the magnet
- (D) The field exists only at the two poles and nowhere else
Show Answer
Answer: C – By convention, magnetic field lines outside a magnet go from the north pole to the south pole. The lines are closest together, and the field is strongest, near the poles.
Q3. A small plotting compass is placed near a bar magnet. The needle of the compass points in the direction of the magnetic field at that point. If the compass is moved closer to the north pole of the magnet, what happens to the needle?
- (A) It stops pointing in any direction
- (B) It points away from the magnet in all positions
- (C) It turns so that it follows the field lines more strongly in the same field direction
- (D) It reverses and points south in every position
Show Answer
Answer: C – A plotting compass always lines up with the local magnetic field. Moving closer to the pole puts it in a stronger field, but the needle still follows the field direction at that point; it does not reverse or stop working.
Q4. A steel paperclip is held against a strong bar magnet for a few minutes and then removed. The paperclip can now pick up small iron pins on its own. Which type of magnet has the paperclip become?
- (A) A permanent magnet
- (B) An induced magnet
- (C) An electromagnet
- (D) A demagnetised magnet
Show Answer
Answer: B – Steel is a magnetically hard material, but the paperclip was magnetised only by being in contact with the magnet, so it is an induced magnet. An induced magnet loses most of its magnetism quickly when removed from the magnetic field, unlike a purpose-made permanent magnet.
Q5. Which material is best for making the core of an electromagnet that must switch on and off quickly?
- (A) Steel, because it stays magnetised for a long time
- (B) Copper, because it is a good electrical conductor
- (C) Soft iron, because it magnetises easily and loses its magnetism quickly
- (D) Aluminium, because it is light
Show Answer
Answer: C – Soft iron is magnetically soft: it becomes magnetic easily when current flows and loses its magnetism quickly when the current stops. Steel stays magnetised, which is wrong for a switchable electromagnet, and copper and aluminium are not magnetic materials.
Q6. A pupil draws the magnetic field pattern around a bar magnet using iron filings. Where are the filings most crowded together?
- (A) At the centre of the magnet
- (B) Halfway between the centre and each pole
- (C) Near the north and south poles
- (D) Evenly over the whole pattern
Show Answer
Answer: C – The filings line up along the field lines. The lines are closest together near the poles, showing that the field is strongest there, so the filings crowd together at the poles.
Q7. Which pair of materials can both be attracted by a magnet?
- (A) Iron and steel
- (B) Copper and aluminium
- (C) Wood and plastic
- (D) Glass and rubber
Show Answer
Answer: A – Iron and steel are magnetic materials and are attracted by a magnet. Copper, aluminium, wood, plastic, glass and rubber are non-magnetic and are not attracted.
Q8. A compass far from any magnet points roughly north. This happens because:
- (A) The compass needle is attracted to the Sun
- (B) The Earth itself acts like a giant magnet with a magnetic field
- (C) The needle is pulled by the Moon’s gravity
- (D) All metals naturally point north
Show Answer
Answer: B – The Earth’s core produces a magnetic field similar to that of a bar magnet. A freely suspended compass needle lines up with this field, so one end points roughly towards geographic north.
Q9. A pupil wants to demagnetise a bar magnet. Which method is most likely to work?
- (A) Painting the magnet blue
- (B) Heating it strongly and then letting it cool without a magnetic field
- (C) Wrapping it in paper
- (D) Placing it next to a wooden ruler
Show Answer
Answer: B – Heating a magnet strongly disturbs the alignment of its magnetic domains, and hammering it has a similar effect. Painting, wrapping or placing it near wood does not change its magnetism.
Q10. An iron nail is hung from a bar magnet and a second iron nail is hung from the first nail, forming a chain. Why does the second nail stay attached?
- (A) The first nail becomes an induced magnet while it is in the magnetic field
- (B) Gravity holds the nails together
- (C) Iron nails are naturally sticky
- (D) The second nail is a permanent magnet
Show Answer
Answer: A – Iron in a magnetic field becomes an induced magnet, so the first nail attracts the second nail. When the bar magnet is removed, the induced magnetism in the nails mostly disappears and the chain falls apart.
Electromagnets and the Motor Effect
Q11. A coil of wire is wrapped around an iron nail and connected to a battery. Which change will NOT increase the strength of the electromagnet?
- (A) Increasing the current through the coil
- (B) Increasing the number of turns on the coil
- (C) Reversing the direction of the current
- (D) Using a thicker iron core inside the coil
Show Answer
Answer: C – Reversing the current reverses the poles of the electromagnet but does not change its strength. More current, more turns and a better core all increase the field strength.
Q12. [Higher tier] A wire of length 0.40 m carries a current of 2.0 A at right angles to a magnetic field of flux density 0.50 T. Calculate the force on the wire.
- (A) 0.10 N
- (B) 0.40 N
- (C) 1.60 N
- (D) 4.00 N
Show Answer
Answer: B – Use F = BIl. Step 1: B = 0.50 T, I = 2.0 A, l = 0.40 m. Step 2: F = 0.50 × 2.0 × 0.40 = 0.40 N.
Q13. [Higher tier] A wire in a magnetic field experiences a force of 0.60 N when the current is 3.0 A and the length of wire in the field is 0.25 m. Calculate the magnetic flux density.
- (A) 0.20 T
- (B) 0.45 T
- (C) 0.80 T
- (D) 4.50 T
Show Answer
Answer: C – Rearrange F = BIl to B = F ÷ (Il). Step 1: Il = 3.0 × 0.25 = 0.75 A m. Step 2: B = 0.60 ÷ 0.75 = 0.80 T.
Q14. [Higher tier] A current-carrying wire is placed between the poles of a magnet. The current is doubled and the length of wire in the field is halved. What happens to the force on the wire?
- (A) It doubles
- (B) It halves
- (C) It stays the same
- (D) It becomes four times larger
Show Answer
Answer: C – From F = BIl, force is proportional to current × length. Doubling I and halving l gives 2 × 0.5 = 1 times the original product, so the force is unchanged.
Q15. Fleming’s left-hand rule is used for the motor effect. In this rule, the first finger, second finger and thumb represent:
- (A) First finger = motion, second finger = field, thumb = current
- (B) First finger = field, second finger = current, thumb = motion (force)
- (C) First finger = current, second finger = motion, thumb = field
- (D) First finger = force, second finger = field, thumb = current
Show Answer
Answer: B – In Fleming’s left-hand rule: the first finger points in the direction of the magnetic field, the second finger points in the direction of the conventional current, and the thumb points in the direction of the motion (force) on the conductor.
Q16. [Higher tier] A wire carries current from east to west in a magnetic field pointing from north to south. Using Fleming’s left-hand rule, what is the direction of the force on the wire?
- (A) Upwards
- (B) Downwards
- (C) Towards the north
- (D) Towards the south
Show Answer
Answer: B – Point the first finger south (field) and the second finger west (current). With the fingers at right angles, the thumb points downwards, so the force on the wire is downwards.
Q17. A simple electric motor spins faster when the current is increased. Why?
- (A) The coil becomes lighter
- (B) The force on each side of the coil increases, so the turning effect increases
- (C) The magnetic field reverses every second
- (D) The commutator stops working
Show Answer
Answer: B – The motor effect force is F = BIl, so a larger current gives a larger force on the coil sides. A larger force gives a larger turning effect (moment), so the coil spins faster.
Q18. What is the job of the commutator (split-ring) in a simple d.c. motor?
- (A) To increase the voltage of the battery
- (B) To reverse the current in the coil every half turn so the coil keeps turning in the same direction
- (C) To make the magnets stronger
- (D) To stop the coil from overheating
Show Answer
Answer: B – Without a commutator, the forces on the coil would reverse every half turn and the coil would just rock back and forth. The split-ring commutator swaps the connections every half turn, reversing the current in the coil and keeping the turning effect in the same direction.
Q19. [Higher tier] A motor coil has sides of length 0.12 m in a field of 0.30 T. Each side carries a current of 1.5 A. Calculate the force on one side of the coil.
- (A) 0.054 N
- (B) 0.36 N
- (C) 0.54 N
- (D) 5.40 N
Show Answer
Answer: A – Use F = BIl. Step 1: B = 0.30 T, I = 1.5 A, l = 0.12 m. Step 2: F = 0.30 × 1.5 × 0.12 = 0.054 N.
Q20. An electromagnet is used in a scrapyard crane to lift cars. When the current is switched off, the car drops. This works because:
- (A) The iron core loses its induced magnetism when the current stops
- (B) The car becomes lighter when the current stops
- (C) Gravity reverses when the current stops
- (D) The coil melts when the current stops
Show Answer
Answer: A – The crane’s core is soft iron, which is only magnetic while current flows in the coil. Switching the current off removes the magnetic field, so the core loses its magnetism and releases the car.
The Generator Effect, Transformers and Sound Devices
Q21. A magnet is moved into a coil of wire connected to a sensitive voltmeter. The voltmeter shows a reading. This is an example of:
- (A) The motor effect
- (B) The generator effect (electromagnetic induction)
- (C) Static electricity
- (D) Magnetic shielding
Show Answer
Answer: B – Moving a magnet relative to a coil changes the magnetic field through the coil and induces a potential difference across its ends. This is the generator effect, the opposite of the motor effect.
Q22. A pupil moves a magnet into a coil slowly, then repeats the experiment moving the magnet in quickly. Compared with the slow movement, the fast movement produces:
- (A) A smaller induced potential difference
- (B) The same induced potential difference
- (C) A larger induced potential difference
- (D) No induced potential difference at all
Show Answer
Answer: C – The size of the induced potential difference depends on the rate of change of the magnetic field. Moving the magnet faster changes the field more quickly, so a larger potential difference is induced.
Q23. An alternator in a power station produces alternating current. How does its output differ from a dynamo that produces direct current?
- (A) The alternator output reverses direction regularly; the dynamo output flows in one direction only
- (B) The alternator output is always zero
- (C) The dynamo output reverses direction regularly; the alternator output does not
- (D) Both outputs are exactly the same
Show Answer
Answer: A – In an alternator, slip rings keep the output alternating as the coil rotates. In a dynamo, a commutator reverses the connections every half turn, so the output current flows in one direction only (direct current).
Q24. [Higher tier] A transformer has 1000 turns on its primary coil and 200 turns on its secondary coil. The primary voltage is 230 V. Calculate the secondary voltage.
- (A) 23 V
- (B) 46 V
- (C) 115 V
- (D) 1150 V
Show Answer
Answer: B – Use Vp ÷ Vs = Np ÷ Ns, so Vs = Vp × Ns ÷ Np. Step 1: Vs = 230 × 200 ÷ 1000. Step 2: 230 × 200 = 46000. Step 3: 46000 ÷ 1000 = 46 V. The secondary has fewer turns, so this is a step-down transformer.
Q25. [Higher tier] A step-up transformer has 100 turns on the primary coil and 2000 turns on the secondary coil. The primary voltage is 230 V. Calculate the secondary voltage.
- (A) 11.5 V
- (B) 230 V
- (C) 4600 V
- (D) 46000 V
Show Answer
Answer: C – Use Vs = Vp × Ns ÷ Np. Step 1: Vs = 230 × 2000 ÷ 100. Step 2: 230 × 2000 = 460000. Step 3: 460000 ÷ 100 = 4600 V. The secondary has more turns, so the voltage is stepped up.
Q26. Electricity is transmitted through the national grid at very high voltage. The main reason is that high voltage:
- (A) Makes the wires lighter
- (B) Reduces the current for the same power, which reduces energy lost as heat in the cables
- (C) Increases the current in the cables
- (D) Stops the wires from rusting
Show Answer
Answer: B – Power transmitted = voltage × current. For a fixed power, a higher voltage means a lower current. Heating loss depends on current, so a lower current wastes much less energy as heat in the transmission cables.
Q27. A transformer works only with alternating current, not direct current. Why?
- (A) Direct current is too dangerous
- (B) A transformer needs a constantly changing magnetic field in its core, which only alternating current produces
- (C) Direct current cannot flow through a coil
- (D) Transformers only work at high voltage
Show Answer
Answer: B – The primary coil must produce a changing magnetic field so that a potential difference is induced in the secondary coil. Alternating current reverses regularly and so produces a changing field; steady direct current produces a steady field, which induces nothing.
Q28. [Higher tier] A loudspeaker converts an electrical signal into sound. Which sequence correctly describes how it works?
- (A) Alternating current in the coil creates a changing magnetic force, the cone vibrates, and the vibrating cone produces sound waves in the air
- (B) Sound waves spin the coil, which generates electricity
- (C) The permanent magnet vibrates on its own and the cone stays still
- (D) Direct current heats the cone until it makes a noise
Show Answer
Answer: A – The alternating current in the loudspeaker coil interacts with the field of the permanent magnet (motor effect). The force reverses with the current, so the coil and attached cone vibrate back and forth, and the cone’s vibrations create sound waves.
Q29. [Higher tier] A microphone converts sound into an electrical signal. Which sequence correctly describes how a moving-coil microphone works?
- (A) Sound waves vibrate a diaphragm attached to a coil, the coil moves in a magnetic field, and a potential difference is induced in the coil
- (B) Sound waves magnetise the diaphragm permanently
- (C) The coil spins like a motor and heats the air
- (D) Sound waves push electrons directly out of the magnet
Show Answer
Answer: A – This is the generator effect in reverse to a loudspeaker: sound vibrates the diaphragm and coil, the moving coil cuts through the magnetic field, and the changing field induces a potential difference that matches the sound pattern.
Q30. [Higher tier] A transformer is 100% efficient. Its primary voltage is 230 V, its secondary voltage is 46 V, and its secondary current is 2.0 A. Calculate the primary current.
- (A) 0.10 A
- (B) 0.40 A
- (C) 2.0 A
- (D) 10 A
Show Answer
Answer: B – For an efficient transformer, Vp × Ip = Vs × Is, so Ip = Vs × Is ÷ Vp. Step 1: Vs × Is = 46 × 2.0 = 92 W. Step 2: Ip = 92 ÷ 230 = 0.40 A. The step-down transformer gives a lower voltage but a higher secondary current, and here the primary current is smaller than the secondary current, as expected.
Keep revising Magnetism and Electromagnetism
Revise every equation on the GCSE Physics Formula Sheet (AQA 8463), then explore the rest of our free physics practice on the Physics MCQs hub, with topic pages for GCSE, IGCSE, A-Level and AP.
All questions on this page are original practice questions written for QuaidianPoint. They are not AQA past-paper questions and this page is not affiliated with AQA.
