GCSE Physics Electricity MCQs – 30 Practice Questions with Answers (AQA 8463)

Thirty original practice questions for AQA GCSE Physics (8463), Topic 2 Electricity, covering circuit symbols, current and charge, potential difference, resistance, series and parallel circuits, IV characteristics, mains electricity, electrical power, domestic appliances, and static electricity and electric fields. Every question has a worked answer hidden underneath it. Use g = 9.8 N/kg in all calculations (where relevant).

Formula recap for Electricity

Charge: Q = I × t  |  Potential difference and resistance: V = I × R  |  Energy transferred by charge: E = Q × V  |  Series resistance: R = R1 + R2  |  Parallel resistance: 1/R = 1/R1 + 1/R2  |  Power: P = V × I and P = I2 × R  |  Energy transferred: E = P × t

Need the full list? Open the GCSE Physics Formula Sheet (AQA 8463).

Circuit Basics: Current, Charge, Voltage and Resistance

Q1. In a circuit diagram, which component is represented by a simple rectangle?

  • (A) A cell
  • (B) A resistor
  • (C) An ammeter
  • (D) A voltmeter
Show Answer

Answer: B – A resistor is drawn as a rectangle in a circuit diagram. A cell is drawn as a long and a short parallel line, an ammeter as a circle with the letter A inside, and a voltmeter as a circle with the letter V inside.

Q2. A current of 2.5 A flows through a torch bulb for 40 s. How much charge passes through the bulb?

  • (A) 16 C
  • (B) 62.5 C
  • (C) 100 C
  • (D) 0.0625 C
Show Answer

Answer: C – Use Q = I × t. Q = 2.5 × 40 = 100 C.

Q3. A 12 V battery is connected across a 4 Ω resistor. What is the current through the resistor?

  • (A) 3 A
  • (B) 48 A
  • (C) 0.33 A
  • (D) 16 A
Show Answer

Answer: A – Use V = I × R, so I = V ÷ R. I = 12 ÷ 4 = 3 A.

Q4. Three resistors of 5 Ω, 10 Ω and 15 Ω are connected in series. What is their total resistance?

  • (A) 3.3 Ω
  • (B) 20 Ω
  • (C) 2 Ω
  • (D) 30 Ω
Show Answer

Answer: D – In series, resistances add: R = 5 + 10 + 15 = 30 Ω.

Q5. A 6 Ω resistor and a 3 Ω resistor are connected in parallel. What is their combined resistance?

  • (A) 9 Ω
  • (B) 2 Ω
  • (C) 18 Ω
  • (D) 0.5 Ω
Show Answer

Answer: B – Use 1/R = 1/6 + 1/3 = 1/6 + 2/6 = 3/6 = 1/2, so R = 2 Ω.

Q6. What is the definition of potential difference?

  • (A) Charge flowing per second
  • (B) Resistance per unit length of wire
  • (C) Energy transferred per unit charge
  • (D) Power used per second
Show Answer

Answer: C – Potential difference is the energy transferred per unit charge passing between two points, measured in volts (1 V = 1 J/C).

Q7. A series circuit contains a battery, a lamp and a resistor. Where in the circuit is the current largest?

  • (A) It is the same everywhere in the circuit
  • (B) Just after the battery
  • (C) Just before the lamp
  • (D) Just after the resistor
Show Answer

Answer: A – In a series circuit there is only one path, so the same current flows through every component.

Q8. Two copper wires have the same thickness, but one is twice as long as the other. How does the resistance of the longer wire compare with that of the shorter wire?

  • (A) It is lower
  • (B) It is the same
  • (C) It is zero
  • (D) It is higher
Show Answer

Answer: D – Resistance increases with the length of the wire, because the current has to pass through more material. The longer wire therefore has the higher resistance.

Q9. A current of 0.5 A flows through a buzzer for 2 minutes. How much charge passes through the buzzer?

  • (A) 30 C
  • (B) 60 C
  • (C) 120 C
  • (D) 240 C
Show Answer

Answer: B – First convert the time to seconds: 2 minutes = 120 s. Then Q = I × t = 0.5 × 120 = 60 C.

Q10. A current of 0.8 A flows through a resistor of 25 Ω. What is the potential difference across the resistor?

  • (A) 31.25 V
  • (B) 0.032 V
  • (C) 25.8 V
  • (D) 20 V
Show Answer

Answer: D – Use V = I × R. V = 0.8 × 25 = 20 V.

Q11. Two lamps are connected in parallel across a 9 V battery. What is the potential difference across each lamp?

  • (A) 4.5 V
  • (B) 18 V
  • (C) 9 V
  • (D) 0 V
Show Answer

Answer: C – Components in parallel are each connected directly across the supply, so each lamp gets the full 9 V.

Q12. A 12 V battery is connected to a 10 Ω resistor and a 20 Ω resistor in series. What is the potential difference across the 10 Ω resistor?

  • (A) 8 V
  • (B) 4 V
  • (C) 12 V
  • (D) 6 V
Show Answer

Answer: B – Total resistance = 10 + 20 = 30 Ω. Current = 12 ÷ 30 = 0.4 A. Potential difference across the 10 Ω resistor = 0.4 × 10 = 4 V. The larger resistor takes the larger share (8 V), which checks: 4 + 8 = 12 V.

IV Characteristics and Series and Parallel Circuits

Q13. Which graph describes an ohmic conductor, such as a resistor kept at constant temperature?

  • (A) A straight line through the origin
  • (B) A curve that flattens as current increases
  • (C) A horizontal line
  • (D) A line that only rises in one direction
Show Answer

Answer: A – For an ohmic conductor, current is directly proportional to potential difference, so the current-voltage graph is a straight line through the origin. Its gradient stays constant because the resistance stays constant.

Q14. [Higher tier] As the current through a filament lamp increases, what happens to the resistance of the filament, and why?

  • (A) It decreases, because the filament cools down
  • (B) It increases, because the filament gets hotter
  • (C) It stays the same, because the lamp is ohmic
  • (D) It drops to zero, because the filament melts
Show Answer

Answer: B – A larger current heats the filament, and the resistance of a metal increases as its temperature rises. The lamp is therefore non-ohmic, and its IV graph curves as the current increases.

Q15. [Higher tier] What does a diode do in a circuit?

  • (A) It allows current to flow in one direction only
  • (B) It allows current to flow equally in both directions
  • (C) It allows current to flow only in the reverse direction
  • (D) It blocks current completely in both directions
Show Answer

Answer: A – A diode has a very low resistance in the forward direction and a very high resistance in the reverse direction, so current flows through it in one direction only.

Q16. [Higher tier] A student plots the IV graph for a diode. In the forward direction the current stays near zero at first, then rises sharply. In the reverse direction the current stays near zero. What does this show?

  • (A) The diode is ohmic
  • (B) The diode has the same resistance in both directions
  • (C) The diode conducts in the forward direction but hardly at all in reverse
  • (D) The diode stores charge like a battery
Show Answer

Answer: C – The sharp rise in the forward direction shows current flowing freely once the diode starts to conduct, while the near-zero reverse current shows that it blocks current in the reverse direction.

Q17. [Higher tier] From an IV graph, a student reads that at a potential difference of 6 V the current through a component is 0.5 A. What is the resistance of the component at that point?

  • (A) 0.083 Ω
  • (B) 3 Ω
  • (C) 6.5 Ω
  • (D) 12 Ω
Show Answer

Answer: D – Use R = V ÷ I. R = 6 ÷ 0.5 = 12 Ω. For a non-ohmic component this value only applies at that point on the graph.

Q18. Two identical lamps are connected first in series and then in parallel across the same battery. In which arrangement are the lamps brighter, and why?

  • (A) Series, because the current is shared equally
  • (B) Parallel, because each lamp gets the full battery voltage
  • (C) Series, because the total resistance is lower
  • (D) Both the same, because the battery voltage is unchanged
Show Answer

Answer: B – In parallel each lamp is connected across the full battery voltage, so each lamp takes its normal current and glows brightly. In series the voltage is shared, so each lamp is dimmer.

Q19. [Higher tier] A light-dependent resistor (LDR) is used in a street-light circuit. What happens to the resistance of the LDR as daylight fades in the evening?

  • (A) It decreases, because less light means lower resistance
  • (B) It increases, because less light means higher resistance
  • (C) It stays the same, because light does not affect it
  • (D) It drops to zero, because the circuit switches off
Show Answer

Answer: B – The resistance of an LDR is high in darkness and low in bright light. As daylight fades, the light intensity falls, so the resistance of the LDR increases.

Q20. [Higher tier] A 4 Ω resistor and a 6 Ω resistor are connected in parallel. This combination is connected in series with a 3.6 Ω resistor across a 12 V battery. What is the current through the battery?

  • (A) 0.5 A
  • (B) 1.2 A
  • (C) 2 A
  • (D) 3.3 A
Show Answer

Answer: C – Parallel part: 1/R = 1/4 + 1/6 = 3/12 + 2/12 = 5/12, so R = 12/5 = 2.4 Ω. Total resistance = 2.4 + 3.6 = 6.0 Ω. Current = 12 ÷ 6.0 = 2 A.


Mains Electricity, Power and Static Electricity

Q21. UK mains electricity has a frequency of 50 Hz. What does this mean?

  • (A) The voltage is always 50 V
  • (B) The alternating current completes 50 full cycles every second
  • (C) The current flows in one direction only, 50 times per second
  • (D) The supply switches off 50 times per second
Show Answer

Answer: B – Mains electricity is alternating current (a.c.): it repeatedly reverses direction. A frequency of 50 Hz means 50 complete cycles per second.

Q22. In a UK three-core mains cable, which wire has brown insulation?

  • (A) The live wire
  • (B) The neutral wire
  • (C) The earth wire
  • (D) The fuse wire
Show Answer

Answer: A – The live wire is brown and carries the alternating potential difference (about 230 V). The neutral wire is blue and the earth wire is green and yellow striped.

Q23. What is the purpose of the earth wire in a metal-cased appliance?

  • (A) To supply power to the appliance
  • (B) To complete the normal circuit
  • (C) To reduce the voltage to a safe level
  • (D) To provide a safe path for current if the live wire touches the case
Show Answer

Answer: D – If a fault makes the metal case live, current flows through the low-resistance earth wire instead of through a person touching the case, and the fuse blows or the breaker trips.

Q24. A kettle is fitted with a 13 A fuse, but a fault causes a current of 20 A to flow. What happens to the fuse?

  • (A) It melts and breaks the circuit
  • (B) It increases its rating to 20 A
  • (C) It stores the extra current
  • (D) Nothing, because fuses only work on direct current
Show Answer

Answer: A – A fuse is a thin wire that melts when the current exceeds its rating. The melted fuse breaks the circuit and stops the current, protecting the appliance and its wiring.

Q25. What is one advantage of a circuit breaker over a fuse?

  • (A) It can carry an unlimited current
  • (B) It never trips
  • (C) It can be reset after it trips, instead of being replaced
  • (D) It works without any electricity supply
Show Answer

Answer: C – A circuit breaker trips and breaks the circuit when the current is too high, but unlike a fuse it can simply be reset and used again once the fault is fixed.

Q26. A washing machine is connected to the 230 V mains and draws a current of 5 A. What is its power?

  • (A) 46 W
  • (B) 1150 W
  • (C) 235 W
  • (D) 46,000 W
Show Answer

Answer: B – Use P = V × I. P = 230 × 5 = 1150 W.

Q27. A current of 3 A flows through a heater element of resistance 20 Ω. What is the power dissipated by the element?

  • (A) 60 W
  • (B) 27 W
  • (C) 120 W
  • (D) 180 W
Show Answer

Answer: D – Use P = I2 × R. P = 32 × 20 = 9 × 20 = 180 W.

Q28. [Higher tier] A polythene rod is rubbed with a dry cloth. The rod becomes negatively charged. What has happened to the rod?

  • (A) It has gained electrons from the cloth
  • (B) It has lost electrons to the cloth
  • (C) It has gained protons from the cloth
  • (D) It has lost neutrons to the cloth
Show Answer

Answer: A – Rubbing transfers electrons between the materials. The rod gains electrons, and because electrons carry negative charge, the rod becomes negatively charged. Protons do not move in this process.

Q29. [Higher tier] Which diagram correctly shows the electric field around an isolated positively charged sphere?

  • (A) Field lines pointing towards the sphere
  • (B) Circular field lines around the sphere
  • (C) Field lines pointing away from the sphere in all directions
  • (D) No field lines, because the field is inside the sphere only
Show Answer

Answer: C – Electric field lines point away from a positive charge and towards a negative charge. Around an isolated positive sphere they are radial lines pointing outwards, and they are closer together where the field is stronger.

Q30. [Higher tier] Two identical balloons are both rubbed so that each carries a negative charge, then they are held close together. What happens, and why?

  • (A) They attract, because opposite charges attract
  • (B) They repel, because like charges repel
  • (C) They do nothing, because static charge has no force
  • (D) They attract, because both are negatively charged
Show Answer

Answer: B – Both balloons carry the same type of charge (negative), and like charges repel each other, so the balloons push apart.

Keep revising Electricity

Revise every equation on the GCSE Physics Formula Sheet (AQA 8463), then explore the rest of our free physics practice on the Physics MCQs hub, with topic pages for GCSE, IGCSE, A-Level and AP.

All questions on this page are original practice questions written for QuaidianPoint. They are not AQA past-paper questions and this page is not affiliated with AQA.