AP Physics 2: Electric Circuits MCQs – 30 Practice Questions with Answers
Test yourself on AP Physics 2 Unit 11 Electric Circuits with 30 original practice questions covering current, resistance, Ohm’s law, series and parallel combinations, power, Kirchhoff’s rules and the qualitative behaviour of RC circuits. All questions are algebra-based: no calculus is used. Every answer includes the full working, using SI units throughout.
Formula recap: current I = ΔQ ÷ Δt; Ohm’s law V = IR; resistance R = ρL ÷ A; power P = IV = I2R = V2 ÷ R; series: Req = R1 + R2 + …; parallel: 1 ÷ Req = 1 ÷ R1 + 1 ÷ R2 + …; loop rule: the sum of potential changes around a closed loop is zero; junction rule: current entering a junction equals current leaving it. Revise all the AP Physics 2 formulas on our AP Physics Formula Sheet.
Current, Resistance and Ohm’s Law
Q1. A charge of 12 C passes a point in a wire in 4.0 s. What is the current?
- (A) 0.33 A
- (B) 3.0 A
- (C) 48 A
- (D) 16 A
Show Answer
Answer: B – I = Q ÷ t = 12 ÷ 4.0 = 3.0 A.
Q2. A resistor has a potential difference of 12 V across it and carries a current of 0.50 A. What is its resistance?
- (A) 6.0 Ω
- (B) 24 Ω
- (C) 0.042 Ω
- (D) 12 Ω
Show Answer
Answer: B – R = V ÷ I = 12 ÷ 0.50 = 24 Ω.
Q3. The voltage across a 20 Ω resistor is doubled. Assuming the resistance stays constant, what happens to the current?
- (A) It halves
- (B) It stays the same
- (C) It doubles
- (D) It quadruples
Show Answer
Answer: C – Ohm’s law I = V ÷ R gives current proportional to voltage at fixed resistance, so doubling V doubles I.
Q4. A wire of length L and cross-sectional area A has resistance R. An identical wire with twice the length has resistance
- (A) R ÷ 2
- (B) R
- (C) 2R
- (D) 4R
Show Answer
Answer: C – R = ρL ÷ A, so resistance is proportional to length. Doubling L doubles R.
Q5. A wire of resistance R is stretched so that its cross-sectional area is halved (its material and volume unchanged, so its length doubles). Its new resistance is
- (A) R ÷ 2
- (B) R
- (C) 2R
- (D) 4R
Show Answer
Answer: D – R = ρL ÷ A. Length doubles (factor 2) and area halves (factor 1 ÷ 0.5 = 2), so R changes by 2 × 2 = 4, giving 4R.
Q6. Conventional current in a metal wire is defined as the direction of flow of
- (A) electrons
- (B) protons
- (C) positive charge, opposite to the electron flow
- (D) neutrons
Show Answer
Answer: C – by convention, current points in the direction positive charge would flow, which is opposite to the actual electron drift in a metal wire.
Q7. A 60 W lamp operates at 120 V. What current does it draw?
- (A) 0.50 A
- (B) 2.0 A
- (C) 7200 A
- (D) 0.20 A
Show Answer
Answer: A – P = IV, so I = P ÷ V = 60 ÷ 120 = 0.50 A.
Q8. A resistor of 10 Ω carries a current of 2.0 A. What power is dissipated as heat?
- (A) 20 W
- (B) 40 W
- (C) 5.0 W
- (D) 200 W
Show Answer
Answer: B – P = I2R = 2.02 × 10 = 4.0 × 10 = 40 W.
Q9. A battery of emf 12 V has an internal resistance of 2.0 Ω. When it delivers a current of 1.0 A, what is the terminal voltage?
- (A) 14 V
- (B) 12 V
- (C) 10 V
- (D) 6.0 V
Show Answer
Answer: C – terminal voltage = emf − Ir = 12 − (1.0 × 2.0) = 10 V.
Q10. Which graph of current against voltage is a straight line through the origin?
- (A) A filament lamp
- (B) A diode
- (C) An ohmic resistor at constant temperature
- (D) A thermistor
Show Answer
Answer: C – an ohmic resistor obeys V = IR with constant R, giving a straight-line I-V graph through the origin. Lamps, diodes and thermistors are non-ohmic.
Series and Parallel Combinations
Q11. Resistors of 4.0 Ω, 6.0 Ω and 10 Ω are connected in series. What is their equivalent resistance?
- (A) 2.1 Ω
- (B) 20 Ω
- (C) 60 Ω
- (D) 0.050 Ω
Show Answer
Answer: B – in series, resistances add: 4.0 + 6.0 + 10 = 20 Ω.
Q12. Resistors of 6.0 Ω and 3.0 Ω are connected in parallel. What is their equivalent resistance?
- (A) 9.0 Ω
- (B) 2.0 Ω
- (C) 4.5 Ω
- (D) 18 Ω
Show Answer
Answer: B – 1 ÷ Req = 1 ÷ 6.0 + 1 ÷ 3.0 = 1 ÷ 6.0 + 2 ÷ 6.0 = 3 ÷ 6.0 = 1 ÷ 2.0, so Req = 2.0 Ω.
Q13. Two identical resistors, each 12 Ω, are connected in parallel across a 12 V battery. What is the total current from the battery?
- (A) 0.50 A
- (B) 1.0 A
- (C) 2.0 A
- (D) 4.0 A
Show Answer
Answer: C – each resistor carries 12 ÷ 12 = 1.0 A, so the total current is 1.0 + 1.0 = 2.0 A. Equivalently, Req = 6.0 Ω and I = 12 ÷ 6.0 = 2.0 A.
Q14. A 12 V battery is connected to two resistors in series, 4.0 Ω and 8.0 Ω. What is the voltage across the 4.0 Ω resistor?
- (A) 12 V
- (B) 8.0 V
- (C) 4.0 V
- (D) 3.0 V
Show Answer
Answer: C – total resistance is 12 Ω, so the current is 12 ÷ 12 = 1.0 A. The voltage across the 4.0 Ω resistor is IR = 1.0 × 4.0 = 4.0 V.
Q15. Two lamps in parallel are connected to a battery. One lamp burns out (its filament breaks). What happens to the other lamp?
- (A) It goes out too
- (B) It stays at the same brightness
- (C) It becomes dimmer
- (D) It becomes brighter, because it gets all the current
Show Answer
Answer: B – in parallel each lamp still has the full battery voltage across it, so its current and brightness are unchanged (ignoring the small effect of internal resistance).
Q16. Three identical bulbs are connected in series across a battery. Compared with a single bulb alone on the same battery, each bulb in the series set is
- (A) brighter
- (B) the same brightness
- (C) dimmer, because the voltage is shared between the three bulbs
- (D) off, because no current flows
Show Answer
Answer: C – each bulb gets only one third of the battery voltage, so each dissipates less power (P = V2 ÷ R) and glows dimmer.
Q17. A 10 Ω resistor and a 30 Ω resistor are in parallel across a battery. How does the current through the 10 Ω resistor compare with the current through the 30 Ω resistor?
- (A) It is one third as large
- (B) It is equal
- (C) It is three times as large
- (D) It is nine times as large
Show Answer
Answer: C – both have the same voltage, so I = V ÷ R: the smaller resistance carries the larger current, in the ratio 30 ÷ 10 = 3.
Q18. A circuit has a 6.0 Ω resistor in series with a parallel combination of two 12 Ω resistors. What is the total equivalent resistance?
- (A) 30 Ω
- (B) 12 Ω
- (C) 18 Ω
- (D) 3.0 Ω
Show Answer
Answer: B – the parallel pair gives 12 ÷ 2 = 6.0 Ω, and adding the series 6.0 Ω gives 12 Ω.
Q19. At a junction, currents of 3.0 A and 2.0 A enter and a current of 1.0 A leaves along one branch. What current leaves along the other branch?
- (A) 1.0 A
- (B) 4.0 A
- (C) 5.0 A
- (D) 6.0 A
Show Answer
Answer: B – by the junction rule, total current in equals total current out: 3.0 + 2.0 = 1.0 + I, so I = 4.0 A.
Q20. A voltmeter is connected across a resistor to measure its voltage. An ideal voltmeter has
- (A) zero resistance, so it takes all the current
- (B) very high resistance, so it takes negligible current
- (C) the same resistance as the resistor
- (D) zero resistance, so it does not change the circuit
Show Answer
Answer: B – a voltmeter is connected in parallel, so it must draw negligible current; an ideal voltmeter has infinite resistance. An ammeter, by contrast, has near-zero resistance and is connected in series.
Power, Kirchhoff’s Rules and RC Circuits
Q21. Two resistors, 10 Ω and 20 Ω, are connected in series across a battery. Which dissipates more power?
- (A) The 10 Ω resistor
- (B) The 20 Ω resistor
- (C) They dissipate equal power
- (D) Neither dissipates power in series
Show Answer
Answer: B – in series the current is the same through both, so P = I2R is larger for the larger resistance: the 20 Ω resistor dissipates twice as much as the 10 Ω resistor.
Q22. Two resistors, 10 Ω and 20 Ω, are connected in parallel across a battery. Which dissipates more power?
- (A) The 10 Ω resistor
- (B) The 20 Ω resistor
- (C) They dissipate equal power
- (D) Neither dissipates power in parallel
Show Answer
Answer: A – in parallel the voltage is the same across both, so P = V2 ÷ R is larger for the smaller resistance: the 10 Ω resistor dissipates twice as much as the 20 Ω resistor.
Q23. A 12 V battery drives a current of 2.0 A through a circuit for 60 s. How much energy is delivered by the battery?
- (A) 24 J
- (B) 144 J
- (C) 1440 J
- (D) 2880 J
Show Answer
Answer: C – power P = IV = 2.0 × 12 = 24 W, and energy = Pt = 24 × 60 = 1440 J.
Q24. In a single-loop circuit with a 9.0 V battery and two resistors, the voltage drops across the resistors are 3.0 V and 6.0 V. This is an example of
- (A) the junction rule
- (B) the loop rule: the drops sum to the emf
- (C) Ohm’s law for a single resistor only
- (D) conservation of charge only
Show Answer
Answer: B – going around the loop, the 9.0 V rise across the battery must be balanced by the drops: 3.0 + 6.0 = 9.0 V, as the loop rule requires.
Q25. A capacitor in series with a resistor is connected to a battery by closing a switch. Immediately after the switch is closed, the capacitor behaves like
- (A) an open circuit (no current)
- (B) a short circuit (maximum current, limited only by the resistor)
- (C) a battery of the same emf
- (D) a resistor equal to the series resistor
Show Answer
Answer: B – the uncharged capacitor initially has zero voltage across it, so the full battery voltage appears across the resistor and the current is at its maximum, V ÷ R.
Q26. After a long time charging, the same RC circuit reaches steady state. The current in the circuit is then
- (A) V ÷ R, unchanged
- (B) twice V ÷ R
- (C) zero, because the capacitor voltage equals the battery voltage
- (D) V ÷ (2R)
Show Answer
Answer: C – when fully charged, the capacitor voltage equals the battery emf, so no voltage remains across the resistor and the current falls to zero. The capacitor then acts as an open circuit for direct current.
Q27. Two RC circuits have the same resistance but different capacitances: circuit A has twice the capacitance of circuit B. How do their charging times compare?
- (A) A charges twice as fast as B
- (B) A takes twice as long to charge as B
- (C) They charge in the same time
- (D) A takes four times as long as B
Show Answer
Answer: B – the charging time scale is the time constant RC. Doubling C doubles RC, so circuit A takes twice as long to reach the same fraction of full charge. No calculus is needed: the time constant grows in proportion to C.
Q28. A fully charged capacitor is disconnected from its battery and then connected across a resistor. As it discharges, the current
- (A) stays constant until the capacitor is empty, then drops to zero
- (B) increases steadily
- (C) is largest at first and then decreases towards zero
- (D) is zero throughout, because the capacitor is disconnected
Show Answer
Answer: C – the initial current is V0 ÷ R. As charge leaves, the capacitor voltage falls, so the current falls with it, approaching zero as the capacitor empties.
Q29. A 100 Ω resistor and a 100 × 10−6 F capacitor are in series. What is the RC time constant?
- (A) 0.010 s
- (B) 0.10 s
- (C) 1.0 s
- (D) 10 s
Show Answer
Answer: A – time constant = RC = 100 × 100 × 10−6 = 10000 × 10−6 = 0.010 s.
Q30. An ammeter is inserted in series in a circuit to measure the current. An ideal ammeter has
- (A) very high resistance
- (B) near-zero resistance, so it does not change the circuit current
- (C) the same resistance as the load
- (D) infinite resistance
Show Answer
Answer: B – an ammeter is in series, so any resistance it adds would reduce the current it is trying to measure. An ideal ammeter therefore has zero resistance; a real ammeter has very small resistance.
Keep revising: work through the other AP Physics 2 sections from the Physics MCQs hub, and keep the AP Physics Formula Sheet open while you practise.
All questions on this page are original practice questions written for QuaidianPoint. They are not College Board past-paper questions and this page is not affiliated with College Board.
